Software / Firmware-Update der Dji Mavic Air - Anleitung

ACHTUNG: Mit der neuen EU Drohnenverordnung muß sich jeder Drohnen-Betreiber beim Luftfahrtbundesamt registrieren und seine Drohne mit der e-ID kennzeichnen! Ein passendes Kennzeichen bekommst Du hier im Shop. Außerdem benötigst Du eine Drohnen-Versicherung. Hier geht es zu unserem Drohnen-Versicherungsvergleich. Informationen zum neuen EU Drohnenführerschein gibt es hier.

  • Software / Firmware-Update der Dji Mavic Air - Anleitung

    Hier eine deutsche Anleitung / Handbuch, wie ein Software-Update bzw. Firmware-Update an der Dji Mavic Air durchzuführen ist.

    In diesem Beitrag werden außerdem unten in den Antworten alle Dji Mavic Air Firmwareupdates und Updates veröffentlicht. Wenn Du einen DJI Mavic Air Quadrocopter besitzt, so abonniere einfach dieses Thema (Du musst im Forum angemeldet sein). Wenn eine neue Version der Software oder Firmware erscheint, so veröffentlichen wir dies hier und Du wirst dann automatisch per eMail benachrichtigt:



    Zu allen anderen Dji Komponenten findest Du eine Übersicht der Update-Beiträge hier.

    Update Anleitung

    Es gibt zwei Möglichkeiten, wie man am DJI Phantom 4 das Update durchführen kann:
    • über die DJI Go App
    • Über den PC / Mac und die Dji Assistant 2 Software via USB Kabel
    Zu bevorzugen ist das Update über die DJI Go App 4 - denn dieses ist viel einfacher und unkomplizierter

    Sollte es via App Probleme geben oder das Update explizit nach dem Download des Updates über die DJI-Seite fragen, dann bitte das Update mit dem PC und der Dji Assistant 2 Software durchführen

    Einzelne Komponenten wie Flight-Controler, Gimbal, Kamera, Akkus etc werden in einem Durchgang upgedatet. Die Dji Go App selbst wird über den AppStore IOS oder den Google PlayStore Android upgedatet / installiert.

    Während eines Updates werden nicht immer zwingend alle Komponenten upgedatet - z.B. Akkus oder Fernsteuerung sind nicht immer betroffen.

    Hier die Anleitungen des Updatevorganges via DJI Go App:






    Update Dji Mavic Air via PC/Mac und Dji Assistant Software

    • zuerst die Dji Assistant 2 Software von der DJI Seite Link zur DJI Webseite herunterladen und auf dem Mac / PC installieren. Bei einer Firewall-Freigabe-Anfrage muss die Freigabe gewährt werden:

    • die DJI Mavic Air mittels USB-Kabel mit dem PC / Mac verbinden und den Assistenten starten.
    • Die DJi Mavic Air einschalten
    • ggf wird eine erneute Firewall-Freigabe abgefragt - diese wieder freigeben
    • in der Assistant Software dann mit dem eigenen Dji Account anmelden oder einen neuen Account erstellen


    • in der Software kann man dann den DJI Mavic Air auswählen und sieht die zur Verfügung stehenden Firmwage Upgrades / Updates
    • diese dann anklicken und installieren
    • (sollte es Probleme mit der aktuell installierten Version geben, kann man hier auch einen Firmware REFRESH machen - also die aktuelle Version erneut installieren - oder einen Firmware DOWNGRADE - also zu einer älteren Firmware-Version zurückgehen)
    • ACHTUNG: die Installation kann bis zu 45 Minuten dauern - WARTEN und nicht ABBRECHEN - keine Verbindungen trennen! Der Kopter startet sich während dieser Zeit ggf. mehrfach neu - trotzdem einfach WARTEN!


    • Der Erfolgreiche Abschluss des Updates (oder eventuelle Probleme) werden nur in der Assistant Software 2 direkt angezeigt:



    Weitere wichtige Anleitungen und Informationen zur Dji Mavic Air

  • Aktuelle Firmware-Version (die neueste steht in der untersten Antwort in diesem Beitrag)
    • Datum: 272.01.2018
    • Aircraft Firmware: v1.0.1.0
    • Remote Controller Firmware: v1.0.0.0
    • DJI GO 4 App iOS: v4.2.5
    • DJI GO 4 App Android: v4.2.4


    Was ist neu?
    • Added SmartCapture.
    • Optimized the Advanced Pilot Assistance Systems performance.
    • Added Boomerang and Asteroid for QuickShot.
    • Added Panorama shooting modes.
    • Added support for DJI Link zur DJI Webseite (requires DJI Link zur DJI Webseite firmware v01.04.0200 or above).
    • Optimized compass calibration.
    • Shorten the time for recognizing propeller guards.
    • Increased the maximum ascend speed to 4 m/s and maximum descend speed to 3 m/s in Sport mode.
    • Improved the flight stability and obstacle detection.
    • Improved accuracy for recognizing subject in Intelligent Flight mode.
    • Improved image quality.
    • Optimized the video transmission.
    Willkommen in unserem Forum!
    Hilfe findet ihr hier >> FAQ
  • Übersicht
    • Datum: 09.02.2018
    • Mavic Air Firmware: v01.00.0200
    • Fernsteuerung: v01.00.0100
    • DJI GO 4 App iOS: v4.2.5
    • DJI GO 4 App Android:v4.2.5



    Was ist neu?
    Dji Mavic Air:
    • Added support for using SmartCapture without a remote controller and DJI GO 4. Added a group photo mode to SmartCapture.
    • Optimized GEO Zone management.
    • Shortened time taken to power off.
    • Optimized transmission quality when transmitting at 2.4 GHz.
    • Improved takeoff performance to dampen a shaking phenomenon experienced by some aircraft during takeoff.
    • Improved takeoff performance when taking off in conditions that are not suitable for the Downward Vision System.
    • Optimized Asteroid exposure settings.
    • Fixed an issue that occasionally prevented the aircraft from taking off following activation.
    • Fixed an issue that occasionally caused the DJI GO 4 app to display a Downward Vision System calibration error.
    • Fixed an issue that caused the battery level display to be incorrect if an Intelligent Flight Battery was not fully charged when used for the first time.
    • Fixed an issue that occasionally caused the aircraft to land unexpectedly.


    Fernsteuerung:
    • Added support for using the DJI Link zur DJI Webseite Head Tracking Flight feature.
    • Shortened time taken to power on.
    • Changed default control stick deadband settings.
    • Fixed an issue that occasionally caused the remote controller restart automatically.
    • Fixed an issue that occasionally caused linking to fail.
    • Fixed an issue that occasionally caused iOS device to start charging and the DJI GO 4 app not to connect to the aircraft when a mobile device was attached using an RC cable.
    • Changed the default settings for the Function button and Customizable button.
    Willkommen in unserem Forum!
    Hilfe findet ihr hier >> FAQ
  • Übersicht
    • Datum: 2018.03.21
    • Aircraft Firmware: v01.00.0300
    • Remote Controller Firmware: v01.00.0100
    • DJI GO 4 App iOS: v4.2.8
    • DJI GO 4 App Android: v4.2.8

    Was ist neu?
    • Increased the descent speed to 3 m/s when flying forward.
    • Added support for operating at 5.8 GHz in Thailand.
    • Fixed an issue where the gimbal would drift when the aircraft’s heading changes.
    • Fixed an issue where the aircraft would shake when using ActiveTrack.
    • Added message if failure to take panoramas or an Asteroid QuickShot occurs (requires DJI GO 4 v4.2.8 and higher).
    • Fixed an issue where the remote controller was unable to link with the aircraft when operating in some regions.
    • Fixed an issue where the aircraft would fail to take a panorama in Sport mode or when APAS is enabled.
    • Fixed an issue where Intelligent Flight Battery firmware would not be updated when functioning abnormally.
    • Fixed an issue of video lag when the aircraft’s heading changes.
    • Fixed an issue of ghosting in photos.
    • Fixed an issue where the aircraft would fail to decelerate automatically when landing.
    Willkommen in unserem Forum!
    Hilfe findet ihr hier >> FAQ