Firmware Update im Anmarsch

    ACHTUNG: Mit der neuen EU Drohnenverordnung muß sich jeder Drohnen-Betreiber beim Luftfahrtbundesamt registrieren und seine Drohne mit der e-ID kennzeichnen! Ein passendes Kennzeichen bekommst Du hier im Shop. Außerdem benötigst Du eine Drohnen-Versicherung. Hier geht es zu unserem Drohnen-Versicherungsvergleich. Informationen zum neuen EU Drohnenführerschein gibt es hier.

    • Firmware Update im Anmarsch

      Es ist für die Inspire ein Firmware Update im Anmarsch, welche das Teil verschlimmbessert.... ;)

      Unter anderem startet das Teil in der Nähe von Flughäfen und dem weißen Haus in Washington nicht mehr. (Flugverbotszonen)

      v1.2.0.34 Firmware Update
      Camera 01.07.24.99 New
      Main Control 02.00.05.10 New
      Gimbal 01.16.00.76 New
      Center Board 02.05.06.01 New
      Air System Encoder 01.11.00.19 New
      Air System Main Controller 01.07.00.03 New
      Battery 03.06.00.00 New
      ESC1,2,3,4 01.03.00.60

      Ground System Decoder 01.07.00.00 New
      Ground System Main Controller 01.08.00.03 New

      Vision Positioning System M0 02.00.00.01 New
      Vision Positioning System M4 01.01.00.01

      Air System USB transmitter 01.01.02.00 New
      Ground System USB transmitter 01.03.01.00 New

      Android APP v1.0.9.3 New
      iOS APP v1.0.3.4 New

      What's changed
      1. No-Fly zone added
      2. Push Aircraft LED status to APP, in order to show pilot the LED status continually
      3. Push the status that battery FULL-CYCLLE charge/discharge is required to APP
      4. Add more detailed description to explain why Aircraft enter P-ATTI/ATTI mode
      5. Reduce the possibility that aircraft switch to P-ATTI automatically when encountering interference or error itself during flight
      6. Optimize the logic about GO-HOME. Allow the pilot to interrupt the aircraft climbing up by moving the accelerator stick up/down after the aircraft arrives 20m altitude.
      7. Push more details to APP when aircraft is in GO-HOME mode
      8. Hold the accelerator stick down at the very bottom for 3s, aircraft can be stopped if it is in takeoff state on the ground
      9. Optimize the IMU calibration user experience
      10. Altitude is limited to min[Maximum Altitude value set by pilot,120m] at most when GPS is not available
      11. Add intelligent landing gear feature, landing gear will raise up at altitude 1.2m (for the 1st time) and down at 0.8m (every time). Pilot can put it ON/OFF in APP
      12. Gimbal will stop moving if it detects that the USB port of camera is connected with other device
      13. Solve the issue that gimbal may drift in sudden frequently during the flight
      14. Optimize gimbal calibration feature
      15. Optimize Vision Positioning System stability
      16. Optimize the OSD display in HDMI device
      17. Allow aircraft initialize and take off from moving surface
      18. Alert user to full cycle charge/discharge to battery if battery not do full cycle charge/discharge for a long time
      19. Alert user to do full charge when the battery is new for the first time flight
      20. APP shows all_in_one firmware number instead of all components.
      21. Add window altering user the distance between the new Home Point and old one when setting RC location as home point.
      22. After upgrading this firmware, compass calibration is required.
      23. After upgrading this firmware, aircraft will be locked. Need connect APP and trigger take-off to unlock.
    • Die Info ist von einem der Betatester, der eigentlich nichts darüber weitergeben sollte.....

      Quelle: Link zum DJI-Forum


      Und DJI Tahoe_ed hat bestätigt, das das "No flight Zone" Feature kommt und nicht abgeschaltet werden kann.

      Hier: Link zum DJI-Forum

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von Knarfboy ()