BeginnerFPV Tiefflieger

Sehr nett
Dankeschön

Hier siehst du den inhalt der backupfile. kannst du kopieren und in eine normale txt File speichern und dann importieren

#

# diff all
###WARNING: NO CUSTOM DEFAULTS FOUND###

# version
# Betaflight / STM32F405 (S405) 4.2.4 Oct 20 2020 / 08:18:45 (fbcaf8c50) MSP API: 1.43
###ERROR: diff: NO CONFIG FOUND###
# start the command batch
batch start

# reset configuration to default settings
defaults nosave

mcu_id 004900343036510837353532
signature

# name: NOVICE-IV

# resources
resource BEEPER 1 B04
resource MOTOR 1 C09
resource MOTOR 2 C08
resource MOTOR 3 B00
resource MOTOR 4 B01
resource MOTOR 5 B06
resource PPM 1 B08
resource PWM 1 B08
resource LED_STRIP 1 B06
resource SERIAL_TX 1 A09
resource SERIAL_TX 2 A02
resource SERIAL_TX 6 C06
resource SERIAL_RX 1 A10
resource SERIAL_RX 2 A03
resource SERIAL_RX 6 C07
resource INVERTER 2 C13
resource I2C_SCL 2 B10
resource I2C_SDA 2 B11
resource LED 1 B05
resource SPI_SCK 1 A05
resource SPI_SCK 2 B13
resource SPI_SCK 3 C10
resource SPI_MISO 1 A06
resource SPI_MISO 2 B14
resource SPI_MISO 3 C11
resource SPI_MOSI 1 A07
resource SPI_MOSI 2 B15
resource SPI_MOSI 3 C12
resource ESCSERIAL 1 B08
resource ADC_BATT 1 C02
resource ADC_CURR 1 C01
resource FLASH_CS 1 A15
resource OSD_CS 1 B12
resource GYRO_EXTI 1 C04
resource GYRO_CS 1 A04
resource USB_DETECT 1 C05
resource PULLDOWN 1 B08

# timer
timer B08 AF3
# pin B08: TIM10 CH1 (AF3)
timer B00 AF2
# pin B00: TIM3 CH3 (AF2)
timer B01 AF2
# pin B01: TIM3 CH4 (AF2)
timer C09 AF3
# pin C09: TIM8 CH4 (AF3)
timer C08 AF3
# pin C08: TIM8 CH3 (AF3)
timer B06 AF2
# pin B06: TIM4 CH1 (AF2)
timer A09 AF1
# pin A09: TIM1 CH2 (AF1)
timer A10 AF1
# pin A10: TIM1 CH3 (AF1)
timer A02 AF2
# pin A02: TIM5 CH3 (AF2)
timer A03 AF3
# pin A03: TIM9 CH2 (AF3)
timer B10 AF1
# pin B10: TIM2 CH3 (AF1)
timer B11 AF1
# pin B11: TIM2 CH4 (AF1)

# dma
dma ADC 1 1
# ADC 1: DMA2 Stream 4 Channel 0
dma pin B00 0
# pin B00: DMA1 Stream 7 Channel 5
dma pin B01 0
# pin B01: DMA1 Stream 2 Channel 5
dma pin C09 0
# pin C09: DMA2 Stream 7 Channel 7
dma pin C08 0
# pin C08: DMA2 Stream 2 Channel 0
dma pin B06 0
# pin B06: DMA1 Stream 0 Channel 2
dma pin A09 0
# pin A09: DMA2 Stream 6 Channel 0
dma pin A10 0
# pin A10: DMA2 Stream 6 Channel 0
dma pin A02 0
# pin A02: DMA1 Stream 0 Channel 6
dma pin B10 0
# pin B10: DMA1 Stream 1 Channel 3
dma pin B11 0
# pin B11: DMA1 Stream 7 Channel 3

# feature
feature -RX_PARALLEL_PWM
feature RX_SERIAL
feature GPS
feature OSD

# serial
serial 0 2048 115200 57600 0 115200
serial 1 2 115200 57600 0 115200
serial 5 64 115200 57600 0 115200

# aux
aux 0 0 0 1800 2100 0 0
aux 1 1 1 1800 2100 0 0
aux 2 13 3 1700 2100 0 0

# vtxtable
vtxtable bands 6
vtxtable channels 8
vtxtable band 1 BOSCAM_A A FACTORY 5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B FACTORY 5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E FACTORY 5705 5685 5665 0 5885 5905 0 0
vtxtable band 4 FATSHARK F FACTORY 5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R FACTORY 5658 5695 5732 5769 5806 5843 5880 5917
vtxtable band 6 IMD6 I CUSTOM 5732 5765 5828 5840 5866 5740 0 0
vtxtable powerlevels 3
vtxtable powervalues 0 1 2
vtxtable powerlabels 25 100 200

# master
set gyro_lowpass2_hz = 188
set dyn_notch_min_hz = 200
set dyn_notch_max_hz = 700
set dyn_lpf_gyro_min_hz = 150
set dyn_lpf_gyro_max_hz = 375
set acc_calibration = 10,-20,26,1
set mag_bustype = I2C
set mag_i2c_device = 2
set mag_hardware = NONE
set baro_bustype = I2C
set baro_i2c_device = 2
set rssi_channel = 9
set serialrx_provider = SBUS
set blackbox_p_ratio = 64
set blackbox_device = SPIFLASH
set dshot_bidir = ON
set motor_pwm_protocol = DSHOT600
set motor_poles = 12
set failsafe_throttle_low_delay = 300
set align_board_yaw = 90
set current_meter = ADC
set battery_meter = ADC
set ibata_scale = 479
set ibatv_scale = 479
set beeper_inversion = ON
set beeper_od = OFF
set yaw_motors_reversed = ON
set small_angle = 180
set gps_provider = UBLOX
set gps_auto_baud = ON
set gps_rescue_angle = 35
set gps_rescue_initial_alt = 100
set gps_rescue_descent_dist = 100
set gps_rescue_ground_speed = 1500
set gps_rescue_min_sats = 6
set runaway_takeoff_prevention = OFF
set osd_vbat_pos = 2434
set osd_rssi_pos = 2426
set osd_link_quality_pos = 344
set osd_rssi_dbm_pos = 376
set osd_tim_1_pos = 161
set osd_tim_2_pos = 2455
set osd_flymode_pos = 2137
set osd_throttle_pos = 312
set osd_vtx_channel_pos = 395
set osd_crosshairs_pos = 14541
set osd_current_pos = 2401
set osd_mah_drawn_pos = 2370
set osd_motor_diag_pos = 238
set osd_craft_name_pos = 2442
set osd_gps_speed_pos = 2232
set osd_gps_lon_pos = 2082
set osd_gps_lat_pos = 2097
set osd_gps_sats_pos = 2241
set osd_home_dir_pos = 366
set osd_home_dist_pos = 2114
set osd_altitude_pos = 2263
set osd_avg_cell_voltage_pos = 354
set osd_esc_rpm_pos = 182
set osd_core_temp_pos = 365
set system_hse_mhz = 8
set debug_mode = GYRO_SCALED
set vtx_band = 1
set vtx_channel = 7
set vtx_power = 3
set vtx_freq = 5745
set max7456_spi_bus = 2
set dashboard_i2c_bus = 2
set flash_spi_bus = 3
set gyro_1_bustype = SPI
set gyro_1_spibus = 1
set gyro_1_sensor_align = CW180
set gyro_1_align_yaw = 1800
set name = NOVICE-IV

profile 0

# profile 0
set dyn_lpf_dterm_min_hz = 84
set dyn_lpf_dterm_max_hz = 204
set dterm_lowpass_type = BIQUAD
set dterm_lowpass2_hz = 180
set p_pitch = 70
set d_pitch = 52
set f_pitch = 75
set p_roll = 70
set i_roll = 90
set d_roll = 50
set f_roll = 70
set p_yaw = 95
set f_yaw = 70
set d_min_roll = 33
set d_min_pitch = 34

profile 1

profile 2

# restore original profile selection
profile 0

rateprofile 0

rateprofile 1

rateprofile 2

rateprofile 3

rateprofile 4

rateprofile 5

# restore original rateprofile selection
rateprofile 0

# save configuration
save
#

Hallo ich kenne mich selber nicht so aus. Was ich dir senden kann ist das backup welches ich per Betaflight gemacht habe.

Hi
Ich habe auch eine novice 4, doch leider habe ich keine Flugeinstellungen auf der Drohne.
Daher meine Frage ob du mir deine Einstellungen irgendwie schicken könntest.